Help I have not gas in carmarthern bottles full (1 Viewer)

[Nanniemate]

I'm in carmerthen my gas bottles are full
But nothing is coming through

I've read the instructions says open us anti clockwise

Tried that no gas so tried anti clockwise
No gas

Am I missing something. It been a while since the gas was used.

Only fitted in August suggestions welcome Basildog your around any ideas please

 

[Jimbohorlicks]

Is there a crash sensor on the regulator that needs pushing in?

 

[Nanniemate]

I'm in carmerthen my gas bottles are full
But nothing is coming through

I've read the instructions says open us anti clockwise

Tried that no gas so tried anti clockwise
No gas

Am I missing something. It been a while since the gas was used.

Only fitted in August suggestions welcome Basildog your around any ideas please

It sys its built in

^{_{Subscribers  do not see these advertisements}}

 

[Sue and Rick]

Turn off gas at the bottle. (as per instructions on bottle)
Then open gas on hob. Like your going to light it.
Turn off gas on hob.
Turn on gas on bottle.

Try as normal.
Did this once on ours and it worked when we knew the bottles were full.

 

[Nanniemate]

Is there a crash sensor on the regulator that needs pushing in?

It says its built in

 

[Nanniemate]

Turn off gas at the bottle. (as per instructions on bottle)
Then open gas on hob. Like your going to light it.
Turn off gas on hob.
Turn on gas on bottle.

Try as normal.
Did this once on ours and it worked when we knew the bottles were full.

Thanks no luck I'll try again when the rainbeades in a minute

^{_{Subscribers  do not see these advertisements}}

 

[Itsmcb]

Take a photo of the regulator whilst your there

 

[Jimbohorlicks]

The regulator thats bolted to the back of the gas locker cupboard not on the bottles.

 

[Nanniemate]

The regulator thats bolted to the back of the gas locker cupboard not on the bottles.

OK I'll have to take the bike off due to the bright idea that once the bike is on you can't open the locker fully

Who's bright idea was that . And it's piddling down

^{_{Subscribers  do not see these advertisements}}

 

[Lenny HB]

It says its built in

That is the anti-rupture valve not the regulator.
Do you have a bottle top regulator or a bulkhead mounted one ?

 

[Nanniemate]

I ant ni David Bailey

 

[Nanniemate]

That is the anti-rupture valve not the regulator.
Do you have a bottle top regulator or a bulkhead mounted one ?

Lenny this is me remember kiss
Speak in stupid i understand that

^{_{Subscribers  do not see these advertisements}}

 

[Nanniemate]

That is the anti-rupture valve not the regulator.
Do you have a bottle top regulator or a bulkhead mounted one ?

 

[Lenny HB]

Ok you have a bulkhead regulator If there is a little green button towards the bottom of the Regulator press it in and old for a few seconds, also if you have a big green button on the hose by the bottle press than in.

 

[lunarman]

There should be a Gas distribution manifold in the van somewhere, are the taps turned to the on position?

^{_{Subscribers  do not see these advertisements}}

 

[Lenny HB]

Also it looks like your regulator is mounted far too low it needs to be above the bottles with the hoses sloping downwards to the bottles.

 

[Nanniemate]

Also it looks like your regulator is mounted far too low it needs to be above the bottles with the hoses sloping downwards to the bottles.

It was fitted by Basildog at autogas2000 not some cowboy back street person

 

[Nanniemate]

There should be a Gas distribution manifold in the van somewhere, are the taps turned to the on position?

Last time I looked at a manifold it was in an Austin 1100

^{_{Subscribers  do not see these advertisements}}

 

[Itsmcb]

Can’t tell from your photo but do you have a yellow button to press in as shown in this photo? It would be out of sight behind the body of the regulator on your setup…

 

[Lenny HB]

Can’t tell from your photo but do you have a yellow button to press in as shown in this photo? It would be out of sight behind the body of the regulator on your setup…
View attachment 864230

That is the over pressure release valve.

 

[Lenny HB]

It was fitted by Basildog at autogas2000 not some cowboy back street person

Charlie's company normally do things correctly maybe your photo makes it look wrong.

^{_{Subscribers  do not see these advertisements}}

 

[Itsmcb]

That is the over pressure release valve.

Are you sure?

 

[Lenny HB]

This is the regulator with the crash sensor green button circled in red.

 

[Lenny HB]

Are you sure?
View attachment 864231

Yes 100%

^{_{Subscribers  do not see these advertisements}}

 

[Lenny HB]

This is the green button on the hose if it has one.

 

[lunarman]

Last time I looked at a manifold it was in an Austin 1100

Should look something like this

 

[Itsmcb]

It would appear there are two types

^{_{Subscribers  do not see these advertisements}}

 

[Nanniemate]

No buttons and for some reason the garage won't let me play with it under their canopy in the dry

Can't understand why not just bought gas off then

 

[Nanniemate]

Should look something like this


View attachment 864234

Can't see anything like that back in the box to have another look

 

[Lenny HB]

Are they new bottles you have just had fitted?
did Autogas do the first fill?

^{_{Subscribers  do not see these advertisements}}