Removing a Ducato swivel seat....Heavy or what!!! (1 Viewer)

[WJACC]

We need to change the leisure battery beneath the seat. I've undone the 6 screws/nuts holding the assembly down. I'd read on other threads the seat assembly was heavy but not quite so heavy!!!

We're only a couple of lightweights, so does anyone know of a knack of doing this or moving it just far enough to access the battery space?

Any help gratefully received...

 

[bigwood]

Not a Ducati but when I had to access the batteries under the drivers seat in our Transit I tipped the seat towards the passenger side rather than completely removing it.
The passenger side was easier not having the bathroom behind the seat but it was certainly heavy and ungainly.

 

[Mixyblob]

I wanted to remove the drivers seat too, on our Ducato based Campscout. I just leant it back, being wary of the cables running through the center of the seat swivel. I had visions of the seat ejecting through the roof of the van if I disconnected them.
What exactly are they and is it ok to disconnect them?

^{_{Subscribers  do not see these advertisements}}

 

[Guigsy]

I wanted to remove the drivers seat too, on our Ducato based Campscout. I just leant it back, being wary of the cables running through the center of the seat swivel. I had visions of the seat ejecting through the roof of the van if I disconnected them.
What exactly are they and is it ok to disconnect them?

Seatbelt pre-tensioner. Theoretically it can go bang. More likely, it'll just cause your airbag warning light to come on. Best to disconnect the cab battery and leave it 10 minutes before you play with it.

 

[mitzimad]

Just disconnect with ignition off it will only show a fault code if you switch ignition on while it's disconected

 

[berni109]

Eco Tree lithium battery part 2.

Finally found the time to get my (prize) battery installed as need it for real use next week. Firstly why aren't batteries made with dimensions that fit into the space where they need to be fitted? After spending a while trying to extract the fitted agm through the hole at the front of the seat...

www.motorhomefun.co.uk

Think this has got the picture of what I did. Slide it across making sure the wires are not trapped.

^{_{Subscribers  do not see these advertisements}}

 

[pagey]

i have 2 batteries under my drivers seat i have no choice but to remove it and as you have found out its very heavy .are you trying to move it while still attached to the swivel? if so dont do them separately as above do not turn the ignition on when you have undone the bolts for the seat you may be able to turn it so the back faces the passenger seat and tip it sideways then remove the swivel from the seat base take photos as you go for replacing it all

 

[WJACC]

i have 2 batteries under my drivers seat i have no choice but to remove it and as you have found out its very heavy .are you trying to move it while still attached to the swivel? if so dont do them separately as above do not turn the ignition on when you have undone the bolts for the seat you may be able to turn it so the back faces the passenger seat and tip it sideways then remove the swivel from the seat base take photos as you go for replacing it all

Yes, I am/was trying to remove them as one unit. So where is the best separation point between the seat and the swivel arrangement?

 

[pagey]

Yes, I am/was trying to remove them as one unit. So where is the best separation point between the seat and the swivel arrangement?

if you slide the seat forwards and backwards you will see the six bolts that attaches the seat to the swivel ,you wont believe how heavy the swivel is on its own

^{_{Subscribers  do not see these advertisements}}

 

[WJACC]

if you slide the seat forwards and backwards you will see the six bolts that attaches the seat to the swivel ,you wont believe how heavy the swivel is on its own

I'll look forward to finding out

 

[Googlebot]

I thought I was going to have an anal prolapse it was so heavy.

I would get someone to help.

 

[Phill D]

I know what is sensible but Is there a set recognised procedure for disconnection of the seat belt pre tension wiring.

^{_{Subscribers  do not see these advertisements}}

 

[pagey]

ok pull the flap at the front of the seat down and you will se a yellow plug in there this is the seat tensioner plug look at it carefully and you will see how it comes apart then thats it

 

[WJACC]

I thought I was going to have an anal prolapse it was so heavy.

I would get someone to help.

If it came to it I think I'd rather sit in the dark Anything anal ain't for me!!

 

[tonyidle]

I used to let the seat with swivel still attached slide / rock forwards to rest on the steering wheel. I found that with a little care I could manoeuvre two lead-acid batteries into place and connect them.

^{_{Subscribers  do not see these advertisements}}

 

[uzsnowdrop]

I used to let the seat with swivel still attached slide / rock forwards to rest on the steering wheel. I found that with a little care I could manoeuvre two lead-acid batteries into place and connect them.

Good tip, I changed the base on my seat to a lowered one ( brilliant bit of kit) but I needed a special tool to lift the seat out , the special tool is called Neil the taxi driver , my mate whos built like a brick outhouse.
If you watch Jennings videos on youtube he is equally ironman , popping the seats out like they are a box of crisps, i tried it and nearly bust a bloodvessel!!

 

[WJACC]

Having split the seat from the base I now know why the ******* thing was so heavy... There were two nuts to undo from the underneath as well as the 6 visible on the top. It was easy when those had been dealt with...

 

[uzsnowdrop]

So you didnt spend half an hour trying to undo the welded nut for the seatbelt fitting before realising its a welded nut… no one would do that would they?

^{_{Subscribers  do not see these advertisements}}

 

[WJACC]

So you didnt spend half an hour trying to undo the welded nut for the seatbelt fitting before realising its a welded nut… no one would do that would they?

Not me

 

[uzsnowdrop]

Not me

Just me then, bugger

 

[pagey]

Having split the seat from the base I now know why the ******* thing was so heavy... There were two nuts to undo from the underneath as well as the 6 visible on the top. It was easy when those had been dealt with...

i have taken the drivers seat out on 2 ducatos never seen bolts underneath just the 6 in the channels

^{_{Subscribers  do not see these advertisements}}

 

[gus-lopez]

i have taken the drivers seat out on 2 ducatos never seen bolts underneath just the 6 in the channels

probably beacuse whoever did it before didn't bother putting them back?

 

[Phill D]

A question for those who have done this.....
I know I could look this up but feeling lazy today
Did you nerd to disconnect the battery prior to unclipping the seat tensioner connections under the seats?

I am also assuming that if you switch on the ignition with the tensioners unplugged then it will require a reset via obd2.

 

[pagey]

no need to disconnect but as you say dont turn the ign on

^{_{Subscribers  do not see these advertisements}}