Alko axle greasing is not at all difficult! (1 Viewer)

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
There are many misguided posts all over the web about this so here it is simplified.
Tales of having to jack up so both rear wheels are off the ground at the same time is both unnecessary and unsafe.
All you need is reasonably level ground with the engine in gear and the wheels chocked.
The handbrake must be OFF!
One side at a time just lift the chassis as though you were going to change the wheel.
Then with a properly bled grease gun pump in several strokes of lithium high melting point grease.
Repeat for the other side and replace the nipple covers.
How easy is that
CA_09171418474799-XL.jpg
 
Last edited:

laneside

Funster
Deceased RIP
Aug 14, 2009
2,668
6,276
Oradour sur Vayres
Funster No
7,981
MH
Rapido V66
Exp
nowhere near long enough
Depends who built the van on some models the grease nipple is not accessible without dropping the axle. Daft I agree
 
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
Depends who built the van on some models the grease nipple is not accessible without dropping the axle. Daft I agree
Sorry I only play with proper vans like Rapidos :D

Subscribers  do not see these advertisements

 
  • Like
Reactions: OG1
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
Actually I did appraise the possibility of this happening and it's a deffo no go for the poor sods (y)

Subscribers  do not see these advertisements

 

Rayb182

Funster
Deceased RIP
Nov 13, 2009
1,523
2,223
Great Bentley
Funster No
9,317
MH
Sundance 590 PR
Exp
Since 1999
Sorry I only play with proper vans like Rapidos :D

Looks like mine underneath, done mine a couple weeks back, one grease nipple wasn't letting any grease through, unscrewed it put a new nipple in, while nipple was out found there was no grease in axle, good job I did it.
 
Jan 28, 2008
10,104
18,259
Dovercourt, Harwich, UK
Funster No
1,353
MH
Renalt burstner
Exp
7 years campers before that
seeing that grease gun took me back i used to grease my brothers artic tand trailer every month for pocket money usually had more on me than on the motor
 
Jan 22, 2013
1,245
58,342
London SE
Funster No
24,385
MH
A class Adria vision I707
Exp
since 1971
Some Alko chassis don't have grease nipples, and are sealed for life,
Mine is that type,
but I would have preferred some then at least you know it's lubricated
 

icantremember

LIFE MEMBER
Sep 2, 2010
8,318
17,526
Near to Watton in Norfolk
Funster No
13,512
MH
Hymer T-SL668
Exp
since 2005
I agree with you Andy that it is a simple job and I do my own regularly .... however I would not work under any vehicle supported on a scissor or hydraulic jack without using axle stands and I'm sure yours are just out of the picture. To enable the axle to hang free the stands need to be under the chassis and not the axle.

Subscribers  do not see these advertisements

 
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
No as the wheel is not removed and there is more than enough clearance under my van for this job.
CA_04071317173425-L.jpg
 
Last edited:

icantremember

LIFE MEMBER
Sep 2, 2010
8,318
17,526
Near to Watton in Norfolk
Funster No
13,512
MH
Hymer T-SL668
Exp
since 2005
I'm sorry to dissagree on this point, maybe mine is lower or I am of larger proportions but I would still not risk it without the stands and would not recommend anyone else does ..... it doesn't add much time to the job and my fire service training has taught me that safety should be a prime concern at all times.
 
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
Yes you must do your own risk assessment with any job.

Subscribers  do not see these advertisements

 
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
My pleasure thank you.
Better picture with a real camera of my ground clearance
DSC_2830-X2.jpg

I don't actually need to get under the van either I can quite easily reach the nipple without
Both sides took about a dozen pumps before the grease started backing up.
DSC_2829-X2.jpg

Subscribers  do not see these advertisements

 

barrywi

Free Member
Sep 25, 2012
120
28
Cumbria
Funster No
23,021
MH
C class
Exp
I am a Newbie to motorhomes but have caravaned for years
Warning . My scissor jack supplied with the vehicle collapsed when I was swopping wheels to paint them. It may have been slightly off vertical , but it made me think about future use of such a device. I now have a four ton bottle jack in the vehicle ( not expensive or particularly heavy) and have bought some new axle stands. I also put my trolley jack under the vehicle when at home for good measure. Better safe than squashed.
My van is 4000 kg rated
 
Sep 28, 2015
1,992
2,553
Kingston upon Hull, East Yorkshire.
Funster No
38,946
MH
Hymer B544
Exp
2001 Caravans 2011 Motorhomes
I know this an old thread but I've just done my 2014 B544 this afternoon, very simple job that Lowdhams wanted £45 to do in addition to the service cost. The difficult thing was getting the alloy wheels off as no grease had been used and they were stuck solid.
I used my trolley jack, axle stands and wheels off as it made it easier to reach.
Check out Granville grease, it meets the Lithium based, extreme pressure requirements.

Subscribers  do not see these advertisements

 

icantremember

LIFE MEMBER
Sep 2, 2010
8,318
17,526
Near to Watton in Norfolk
Funster No
13,512
MH
Hymer T-SL668
Exp
since 2005
I know this an old thread but I've just done my 2014 B544 this afternoon, very simple job that Lowdhams wanted £45 to do in addition to the service cost. The difficult thing was getting the alloy wheels off as no grease had been used and they were stuck solid.
I used my trolley jack, axle stands and wheels off as it made it easier to reach.
Check out Granville grease, it meets the Lithium based, extreme pressure requirements.
Why did you have to remove the wheels? ... I do mine easily with them insitu.
 
Sep 28, 2015
1,992
2,553
Kingston upon Hull, East Yorkshire.
Funster No
38,946
MH
Hymer B544
Exp
2001 Caravans 2011 Motorhomes
The side skirting bodywork comes down quite a bit for access and to get my axle stands in securely I would have had to jack it quite a bit higher. Plus, taking them off is an opportunity to have a look at the tyres and brakes.
I noticed on Lowdhams service plan it says 'without removing road wheel', one of the things that put me off.
Because it's a very simple thing to take the wheels off (when they are not seized) it seems sensible to give myself more space/light.
 
Aug 18, 2014
23,537
131,293
Lorca,Murcia,Spain
Funster No
32,898
MH
Transit PVC
Exp
16 years since restarting
How many pumps pers side would be considered normal each year ?
I've just done my mate's & it took 46 each side + one new nipple as it wouldn't reseal.

Subscribers  do not see these advertisements

 
OP
OP
Techno

Techno

LIFE MEMBER
Deceased RIP
Jul 28, 2010
15,475
20,752
Leeds the one up North
Funster No
12,905
MH
Rapido 7090F 3 litre 160
Exp
May 2010
7 to 12 on mine as soon as it starts backing up out of the nipple. Did you check the gun was primed fully first and not pumping air
 
Aug 27, 2009
19,788
23,032
Hertfordshire
Funster No
8,178
MH
Van Conversion
Exp
40 years
There are many misguided posts all over the web about this so here it is simplified.
Tales of having to jack up so both rear wheels are off the ground at the same time is both unnecessary and unsafe.
All you need is reasonably level ground with the engine in gear and the wheels chocked.
The handbrake must be OFF!
One side at a time just lift the chassis as though you were going to change the wheel.
Then with a properly bled grease gun pump in several strokes of lithium high melting point grease.
Repeat for the other side and replace the nipple covers.
How easy is that
CA_09171418474799-XL.jpg
I last did this some years ago when I had an Alko set up. Glad to see the method hasn't changed since then.(y)

Subscribers  do not see these advertisements

 

Join us or log in to post a reply.

To join in you must be a member of MotorhomeFun

Join MotorhomeFun

Join us, it quick and easy!

Log in

Already a member? Log in here.

Latest journal entries

Funsters who are viewing this thread

Back
Top