Autogas 2000 Ltd

Discussion in 'Motorhome Chat' started by Ambilkate, Nov 3, 2015.

  1. Ambilkate

    Ambilkate Funster Life Member

    Joined:
    Jul 15, 2009
    Messages:
    4,109
    Likes Received:
    6,668
    Location:
    Shropshire
    Had to 11's lightweight fitted yesterday by Auto gas 2000 Ltd popped in there on the way way back from Whitby neat Job Bill was pleased with their work and would recommend them to you plus we did get a funster discount :)
    gas.jpg gas1.jpg gas2.jpg
     
    • Like Like x 7
  2. andy63

    andy63 Funster

    Joined:
    Jan 19, 2014
    Messages:
    1,846
    Likes Received:
    6,422
    Location:
    south shields
    Nice.. what are the two fittings in the top photograph??
    One below the sill and the top one in the body panel..
    I'm assuming one is a fill point..
    Ta andy
     
  3. andy63

    andy63 Funster

    Joined:
    Jan 19, 2014
    Messages:
    1,846
    Likes Received:
    6,422
    Location:
    south shields
    Haha just had a closer look... its the locker door handle...:whistle:(n)
     
    • Like Like x 5
  4. hilldweller

    hilldweller Funster Life Member

    Joined:
    Dec 5, 2008
    Messages:
    26,421
    Likes Received:
    25,078
    Location:
    Macclesfield
    Is that filler high enough ?
     
    • Like Like x 2
  5. PeteH

    PeteH Funster

    Joined:
    Nov 22, 2007
    Messages:
    1,752
    Likes Received:
    2,164
    Location:
    East Yorkshire
    Same though just crossed my mind too?. Could be problematic on some sites I've been on?. and the odd Ferry ramp?

    Pete
     
    • Like Like x 1
  6. Ambilkate

    Ambilkate Funster Life Member

    Joined:
    Jul 15, 2009
    Messages:
    4,109
    Likes Received:
    6,668
    Location:
    Shropshire
    They fitted it Brian so i do hope so
    Kate x
     
    • Like Like x 1
  7. hilldweller

    hilldweller Funster Life Member

    Joined:
    Dec 5, 2008
    Messages:
    26,421
    Likes Received:
    25,078
    Location:
    Macclesfield
    What worries me is it looks just where I've caught our nearside skirt twice, once on a low iron bollard on a pavement corner and then on some wood in a garden parking. At least you can think about it.
     
  8. Ambilkate

    Ambilkate Funster Life Member

    Joined:
    Jul 15, 2009
    Messages:
    4,109
    Likes Received:
    6,668
    Location:
    Shropshire
    will get Bill to take another look at it tomorrow the locker next to it is lower and the exhaust is lower that the locker will take a better pic tomorrow . Got me worried now Brian but thanks xxx Kate
     
  9. Minxy Girl

    Minxy Girl Funster Life Member

    Joined:
    Aug 22, 2007
    Messages:
    8,503
    Likes Received:
    9,859
    Location:
    E Yorks
    If you look to the left in one of the photos you can see the locker which appears to be even lower.
     
  10. scotjimland

    scotjimland Funster Life Member

    Joined:
    Jul 25, 2007
    Messages:
    28,934
    Likes Received:
    25,574
    Location:
    .
    wouldn't be too concerned.. it is still higher than the chassis rail.. (which you can just about see ) and as Mel said. the step
     
  11. Ambilkate

    Ambilkate Funster Life Member

    Joined:
    Jul 15, 2009
    Messages:
    4,109
    Likes Received:
    6,668
    Location:
    Shropshire
    gas2.jpg Brian if you look at the locker below the orange running light the filling point is way above that but will let Bill know thanks again x Kate
    ps sorry didnt see other posts of MinxyGirl and ScotJimland
     
  12. hilldweller

    hilldweller Funster Life Member

    Joined:
    Dec 5, 2008
    Messages:
    26,421
    Likes Received:
    25,078
    Location:
    Macclesfield
    I don't think so, when the gas locker is down the bottom line will be straight. Now you've made me look again I like it even less. Just to the left there looks to be a small panel under an amber reflector, I would like to see it there, if it were mine. Or even where that reflector is.

    It sure would not add to a holiday if this gets knocked off.
     
  13. PeteH

    PeteH Funster

    Joined:
    Nov 22, 2007
    Messages:
    1,752
    Likes Received:
    2,164
    Location:
    East Yorkshire
    I don't think the issue would be in "normal" operation. It might be tricky if you went too close to an object on that side when manoeuvring? OR as I previously observed, ferry ramps, some of which have "Fingers" which can Jamb and leave just one raised. I know that I've been tasked with the job of "fixing" them before today! Usually a large hammer and grease gun! I even burned one off once with an Oxy set! the "owner" was half pleased! when they got the bill!.

    Pete
     
  14. Minxy Girl

    Minxy Girl Funster Life Member

    Joined:
    Aug 22, 2007
    Messages:
    8,503
    Likes Received:
    9,859
    Location:
    E Yorks
    Yes, below the reflector in the little bit of panel would have been better I agree, I wonder if there was something in the way?
     
    • Like Like x 1
  15. meggie

    meggie Funster

    Joined:
    Jan 12, 2009
    Messages:
    181
    Likes Received:
    331
    Location:
    milford haven
    They done a nice job should save a few £ now
     
    • Like Like x 2
  16. hilldweller

    hilldweller Funster Life Member

    Joined:
    Dec 5, 2008
    Messages:
    26,421
    Likes Received:
    25,078
    Location:
    Macclesfield
    Sorry but I when I see a possible problem I just can't say nothing, that would really be letting you down.
     
    • Like Like x 2
  17. Gorse Hill

    Gorse Hill Funster

    Joined:
    Feb 2, 2013
    Messages:
    1,395
    Likes Received:
    1,603
    Location:
    Stretford
    Have to agree with Brian, my first thought was it looks low (roughly about the centre of the wheel if not lower looking at the photo but could be deceiving depending on the angle)
    Am sure Autogas, who have a very good reputation, would sort it if you were concerned about the height being a potential problem
     
  18. campa cola

    campa cola Funster

    Joined:
    Oct 5, 2012
    Messages:
    2,802
    Likes Received:
    5,648
    Location:
    Weegeland
    I am pretty sure the monster urban speed bumps I had to negotiate today that would have taken that inlet valve off!!
     
  19. scotjimland

    scotjimland Funster Life Member

    Joined:
    Jul 25, 2007
    Messages:
    28,934
    Likes Received:
    25,574
    Location:
    .
    That is where I fitted mine.. nothing in the way.. the bit of pipe insulation you can see is covering a short piece of ally angle I fitted to stop the panel flexing when filling.. the fill hose is resting on it.. didn't want it chaffing.

    you can also see clearly in this photo where the chassis rail is
     

    Attached Files:

    • Like Like x 2
  20. Manic

    Manic Funster

    Joined:
    Nov 4, 2011
    Messages:
    856
    Likes Received:
    991
    Location:
    Uk
    QUOTE="hilldweller, post: 1614263, member: 5089"]I don't think so, when the gas locker is down the bottom line will be straight. Now you've made me look again I like it even less. Just to the left there looks to be a small panel under an amber reflector, I would like to see it there, if it were mine. Or even where that reflector is.

    It sure would not add to a holiday if this gets knocked off.[/QUOTE]

    It looks low to me too, I fitted mine in the panel to the right of the gas locker.
    image.jpg image.jpg [
     
Loading...

Share This Page